Checking phase sequence of 3 phase supply

Tuesday - 14/08/2018 11:33
The correct phase sequence is required for the proper operation of any three phase system. It ensures that the load works as desired, when incorrect, the equipment such as the motor may malfunction, rotate in the reverse direction.
Checking phase sequence of 3 phase supply
Checking phase sequence of 3 phase supply

The phase reversal may damage the motor or the equipment the motor is driving. It is always important to ensure that the incoming 3-phase conductors have the correct phase sequence before connecting new equipment or before reconnecting motors after maintenance. This might not be obvious by visual inspection, hence the need for a reliable tool.
 

motor roto


The two commonly used methods are the rotating phase-sequence meter or the static phase-sequence indicator. Test tools are used to confirm that the connection to motors and other three phase equipment is done right before commissioning. In addition, the phase-sequence indicators are used in confirming the wiring in switchboards with a three phase supply.

Phase sequence meter/indicator

The phase-sequence meter is the most straightforward and commonly used tool for determining the phase sequence. The meter may be digital using semiconductor devices, or rotational (analog) type.

Rotational phase sequence meter

These are small asynchronous motors consisting of an aluminum disk which serves as the rotor. The tester has three windings which are usually connected to the circuit under test. The principle of operation is similar to that of an induction motor.

The meter has coils whose one end of each is connected in a star configuration. The other three ends of the coils are attached to the motor power connections or the circuit under test. The meter contains an aluminum disk which rotates when the current through the coils creates a magnetic field.

The current through the three windings creates a magnetic field that depends on the phase sequence of the incoming power conductors, this causes the disk to rotate in the direction that depends on phase sequence. The meter terminals are marked with a certain phase sequence order. Once the disk rotates, the direction of the arrow on the disk shows the phase sequence, based on the marks.

The tool rotates clockwise when the phase sequence is correct (RYB) and anticlockwise when the phases are reversed.

Some general-purpose indicators may determine the phase sequence, power factor and phase shift between the current and voltage.

Static Type Phase-Sequence Indicators

The static indicator is a simple configuration that uses two lamps and an inductor or capacitor. One lamp is connected to one phase such as R and the other to another phase such as Y, while the inductor or capacitor on the remaining third phase. A resistor may be used in series with the lamp to control the amount of current and voltage.

If using the inductor, lamp B will be more brighter than A if the phase sequence is correct, while Lamp A becomes brighter when the phases are reversed.

However, using the capacitor tester, Lamp A will light on while lamp B will be off. If the sequence is incorrect, lamp B lights up while lamp A remains off.

Conclusion

In three-phase equipment such as motors and measuring instruments, the correct phase sequence determines whether the motor will rotate in the right direction, or if the instrument works as expected. However, the phase sequence may not be obvious and it is important to have a means of verifying that the sequence is correct, otherwise the system may not function properly or as expected.

The two commonly used methods are the phase sequence meter or the static indicator. The meter is simple and easy to use, but is more costly. On the other hand, the static indicator is cheap and easy to make and use.

Total notes of this article: 0 in 0 rating

Click on stars to rate this article

  Reader Comments

Security Code   
online
  • Support

    Sales Manager

    +(84)923.886.133

    dolin@dolin.com.vn

    Sales 01

    +(84)918.26.11.44

    dolinvn@dolin.com.vn

    Sales 02

    +(84)941.976.189

    info@dolin.com.vn

    Sales 03

    +(84)923.886.191

    sales@dolin.com.vn

    Sales 04

    +(84)949.380.913

    dolinsales@dolin.com.vn

    Sales 05:

    +(84)987.246.757

    dolin@dolin.com.vn

Google+
Bestsellers
Software
CNC Machine
Construction and Land
Counter
  • Online55
  • Today2,425
  • This month281,111
  • Total8,908,813
You did not use the site, Click here to remain logged. Timeout: 60 second